🔒 Closed Help 936 openline after flash white led only

[TheReturnOfRomansa]

after po ng white led pa guide jumper tut ginaya ko yung kay sir jansen ramos po...

nasa white led na ako after successfull flashing po salamat sa tutulong ..

wait ko ba mag red light?

 

[TheReturnOfRomansa]

thinkster03

 

[t h i n k s t e r]

nasa reset ka na di ba?

 

[TresMarias]

power off
connect jumper
plug-in supply/power
release jumper
flash usbloader.bin(power light only na yan)
flash firmware(blue light with 2 signal bar)
success (babalik yan sa power light only)
re-connect supply/power
dapat OK na yan

 

[Shinsuke Nishizono]

Nakita lang to.

You do not have permission to view the full content of this post. Log in or register now.

 

[henji]

tag syringe , BlackArchAngel , BeChay

 

[TheReturnOfRomansa]

nasa reset ka na di ba?

ulitin ko una saksak ko lahat diba tapos detect ko sa balong?
tapos load ko si bin hayaan ko lang hanggat ma detect nya si com port?

 

[TheReturnOfRomansa]

power off
connect jumper
plug-in supply/power
release jumper
flash usbloader.bin(power light only na yan)
flash firmware(blue light with 2 signal bar)
success (babalik yan sa power light only)
re-connect supply/power
dapat OK na yan

di ko na gagamitin si balong? usb loader?

 

[t h i n k s t e r]

ulitin ko una saksak ko lahat diba tapos detect ko sa balong?
tapos load ko si bin hayaan ko lang hanggat ma detect nya si com port?

Make sure nayung LAN card ay napili mo ng sakto sa “Network Card” option

 

[delloCM_]

https://phcorner.org/t/openline-and-full-admin-tut-for-globe-936.288188/

 

[TresMarias]

di ko na gagamitin si balong? usb loader?

natural gagamitin, yan kasi ang flasher ni usbloader.bin

remember, release jumper if detect na sya sa PC, then start balong and flash firmware

 

[TheReturnOfRomansa]

power off
connect jumper
plug-in supply/power
release jumper
flash usbloader.bin(power light only na yan)
flash firmware(blue light with 2 signal bar)
success (babalik yan sa power light only)
re-connect supply/power
dapat OK na yan

pag ka blue pag ka success hintayin ko muna mamatay and magwhite ulit bago ko hugutin power chord tapos balik power chord
ginawa ko kasi pagkasuccess ni flash remove baterry aalisin ko na agad nakablue light pa sya

 

[TheReturnOfRomansa]

ayun guys red light na with 2 signal sa dulo ano na next nito?

 

[TresMarias]

pag ka blue pag ka success hintayin ko muna mamatay and magwhite ulit bago ko hugutin power chord tapos balik power chord
ginawa ko kasi pagkasuccess ni flash remove baterry aalisin ko na agad nakablue light pa sya

hintayin mo muna bumalik sa power light only after success, kusang mag turn off yan blue light at 2bars signal

 

[delloCM_]

power off
connect jumper
plug-in supply/power
release jumper
flash usbloader.bin(power light only na yan)
flash firmware(blue light with 2 signal bar)
success (babalik yan sa power light only)
re-connect supply/power
dapat OK na yan

release jumper lang yan pag tapos.na.flash

 

[delloCM_]

release jumper lang yan pag tapos.na.flash

bkit.mo aalisin ng hindi kpa nagflash

 

[TresMarias]

release jumper lang yan pag tapos.na.flash

hahahaha boot testpoinnt lang yan para maka recovery mode na si 936, after noon puedi mona i-release si jumper,

tested many many many many times

 

[TheReturnOfRomansa]

release jumper lang yan pag tapos.na.flash

ok na bali pag baliko ko ng power and release jumper pumunta na sya sa red light + 2 signal bar sa dulo ano next nyan?

 

[TresMarias]

ok na bali pag baliko ko ng power and release jumper pumunta na sya sa red light + 2 signal bar sa dulo ano next nyan?

as i've said, release jumper after ma detect na sya ng PC, then start balong then flash mo na

 

[delloCM_]

ok na bali pag baliko ko ng power and release jumper pumunta na sya sa red light + 2 signal bar sa dulo ano next nyan?

sundan mo lang tamang procedure wag gawin ang wala sa instruction para iwas brick reflash mo lang yan ook yan