What's new
By:

❓ Help Baka may same experience kayo about this.

Status
Not open for further replies.
C

ChrolloLucifer

Established
I have a question about mixing different brands of NVMe M.2 drives. After I installed a Kingston NV2, my boot-up time increased significantly to about 20 seconds, when it used to take only 5-7 seconds. I am using a Crucial P1 500GB for my OS and a Kingston 1TB NV2 for storage on an MSI B450 Mortar board. Every time I boot up, my Debug LED gets stuck on GPU, but when I tested the GPU on another PC, it worked perfectly. I'm not sure what to do next. Sa Debug LED naman mag stuck siya dun mga 20 secs nga then pag load na perfeclty fine naman yun system. Talagang yung bootup ang naging issue ko.
 
Sort by date Sort by votes
It seems like you are experiencing some issues with your system booting up after installing a new Kingston NV2 NVMe M.2 drive alongside your existing Crucial P1 drive. Here are some possible reasons for the increased boot-up time and the Debug LED getting stuck on GPU:

1. Incompatibility between NVMe drives: Mixing different brands of NVMe drives can sometimes lead to compatibility issues. Different drives may have different firmware, controllers, or other hardware components that could cause conflicts.

2. BIOS settings: Make sure that your BIOS settings are properly configured to support multiple NVMe drives. Sometimes, adjusting settings related to storage devices in the BIOS can help with compatibility issues.

3. Driver conflicts: Ensure that you have the latest drivers installed for both your NVMe drives. Sometimes outdated drivers or conflicting drivers can cause performance issues.

4. GPU-related issue: The fact that the Debug LED gets stuck on GPU during boot-up could indicate a GPU-related issue. This may be unrelated to the NVMe drives. You could try reseating the GPU, checking the power connections, or updating the GPU drivers to see if that resolves the problem.

5. Testing components: Since your GPU works fine in another PC, it's possible that the issue lies with the motherboard or other components in your system. You could try testing different combinations of components or swapping out certain parts to identify the root cause of the boot-up issue.

6. Check for firmware updates: Ensure that both your motherboard and NVMe drives have the latest firmware updates installed. Manufacturers frequently release updates to address compatibility issues and improve performance.

7. Consult manufacturer support: If you've tried troubleshooting on your own and are still experiencing issues, consider reaching out to the manufacturer's support for your NVMe drives, GPU, and motherboard. They may have specific recommendations or solutions tailored to your setup.

In conclusion, the issues you are facing could be due to a variety of factors, including compatibility issues, settings configurations, driver conflicts, or hardware problems. By systematically troubleshooting each potential cause, you may be able to identify and resolve the issue affecting your system's boot-up time.
 
Upvote 1 Downvote
mixing brands has nothing to do with it. its just a storage. pero alam ko yang problema mo. faulty SSD yan. error LED ON + long time booting. failing yung SSD mo. sooner or later. hindi na yan ma dedetect ng PC. e test mo yan SSD sa ibang PC.
 
Upvote 0 Downvote
bingjalz said:
mixing brands has nothing to do with it. its just a storage. pero alam ko yang problema mo. faulty SSD yan. error LED ON + long time booting. failing yung SSD mo. sooner or later. hindi na yan ma dedetect ng PC. e test mo yan SSD sa ibang PC.
Click to expand...
pwedeng ito, try mo din i reset bios tas re setup ulit. incase same2 paden either ssd/mobo yan.
 
Upvote 0 Downvote
syet sa shopee ko lang na order to sa wholesale master :( since good review naman yun shop at madalas din ako bumibili dun ng mga flash drives. Pero ngayon lng ako nag try ng SSD sa kanila.. yung DEBUG LED ng GPU ko wala siya nung unang hindi pam ko nag iinstal ng driver ng GPU. Naka ilang restart ako smooth ang boot up pero nung nag install na ko ng Andrenalin. Bumalik yung ganon bagal ng boot up.

PHC-ILULU said:
pwedeng ito, try mo din i reset bios tas re setup ulit. incase same2 paden either ssd/mobo yan.
Click to expand...
this i dont know how. Sa Google lang ako kasi tumitingin tingin eh.
 
Upvote 0 Downvote
ChrolloLucifer said:
syet sa shopee ko lang na order to sa wholesale master :( since good review naman yun shop at madalas din ako bumibili dun ng mga flash drives. Pero ngayon lng ako nag try ng SSD sa kanila.. yung DEBUG LED ng GPU ko wala siya nung unang hindi pam ko nag iinstal ng driver ng GPU. Naka ilang restart ako smooth ang boot up pero nung nag install na ko ng Andrenalin. Bumalik yung ganon bagal ng boot up.
Click to expand...
you mean nka salpak na yung bago mong SSD at smooth pa boot up? bumagal lng nung nag install kna ng adrenalin? i doubt thats the cause. ksi ang purpose ng POST is to make sure every hardware is fine before the PC boots up. kung matagal mag boot ang PC at may LED error. means something is wrong physically.
 
Upvote 0 Downvote
bingjalz said:
you mean nka salpak na yung bago mong SSD at smooth pa boot up? bumagal lng nung nag install kna ng adrenalin? i doubt thats the cause. ksi ang purpose ng POST is to make sure every hardware is fine before the PC boots up. kung matagal mag boot ang PC at may LED error. means something is wrong physically.
Click to expand...
yan din ang nasa isip ko eh pero ayun talaga yun nangyari eh gulong gulo utak ko haha
 
Upvote 0 Downvote
post pcie scan

need to remember pcie lanes ang ginagamit ng nvme and hindi na sata lanes guess what else gumagamit ng pcie lanes
GPU

more pcie lanes used more time needed for system scan specially if limited yung pcie lanes ng mobo mo

pero this doesn't rule out if my defect or pagit yung controller nung 2nd ssd since post slow down is senyas ng ganyan

try mo gawing boot yung bagong ssd gawa ka partition lagyan mo os then tignan mo post speed ng magisa sya to make sure

tandaan mo rin na yung cruxial p1 is my dram so mas mabilisnsya mg post scan kysa sa nv2 na walang dram
 
Upvote 0 Downvote
sasame9821 said:
post pcie scan

need to remember pcie lanes ang ginagamit ng nvme and hindi na sata lanes guess what else gumagamit ng pcie lanes
GPU

more pcie lanes used more time needed for system scan specially if limited yung pcie lanes ng mobo mo

pero this doesn't rule out if my defect or pagit yung controller nung 2nd ssd since post slow down is senyas ng ganyan

try mo gawing boot yung bagong ssd gawa ka partition lagyan mo os then tignan mo post speed ng magisa sya to make sure

tandaan mo rin na yung cruxial p1 is my dram so mas mabilisnsya mg post scan kysa sa nv2 na walang dram
Click to expand...
pano to? i mean scan talaga?
 
Upvote 0 Downvote
sasame9821 said:
what i mean is everytime na mag boot ka ng system ng scascan sya ng pcie lanes in post

if my beep speaker yung motherboard mo ito yung time na parang wala sya ginagawa bago mag beep
Click to expand...
ayun nga yun iniisip ko. one beep lang siya tulad dati then naka debug led lang siya gpu ng for about 20 secs lang tapos pag nag load na. Normal na siya. Inayos ko naman boot set up niya pero ganon parin
 
Upvote 0 Downvote
then its normal
since dalawana nvme mo dalawang scan na gagawin nya
if gusto mo makuha yun dati mong boot speed
then gawin mong portable drive yung 2nd nvme para hindi nya isali sa post scan

other than that live with it like seriously 20 second is very minimal para sa boot time
now if 20 mins then my malaking problema but 20 seconds no

if gusto mo lightning fast as in wala pang 1 sec yung boot mo then i on mo yung hybrid sleep ng pc mo
then i setup mo na yun yung gawin nya pag pinindot mo yung power button sa power setting

kase right now there is no problem here
 
Upvote 1 Downvote
sasame9821 said:
then its normal
since dalawana nvme mo dalawang scan na gagawin nya
if gusto mo makuha yun dati mong boot speed
then gawin mong portable drive yung 2nd nvme para hindi nya isali sa post scan

other than that live with it like seriously 20 second is very minimal para sa boot time
now if 20 mins then my malaking problema but 20 seconds no

if gusto mo lightning fast as in wala pang 1 sec yung boot mo then i on mo yung hybrid sleep ng pc mo
then i setup mo na yun yung gawin nya pag pinindot mo yung power button sa power setting

kase right now there is no problem here
Click to expand...
oh now i na intindihan ko na! thank you!
 
Upvote 0 Downvote
UPDATE!

Hello, I'm back!!!

User problem pala to sorry na agad haha

So ganito, hindi ko pala na indicate dito na kaya ako nag install ng bagong M.2 for storage is faulty na yung lumang HHD ko o_O
Then ako naman si kamote nung dumating sinalpak ko na agad siya. Not knowing na hindi ko pala na alis yung connection ng sirang HHD o_O

Then ngayon binuksan ko uli sabi ko baka makuha pa sa reseat ng hardwares at nag reset bios pa nga ako. Tapos napansin ko yung Sata na isa naka saksak pa sa board ko. So inalis ko kasi bat nakasaksak eh hindi ko na ginagamit yun at inalis ko na sa device manager yun. Naka hide na yun Drive na yun. Pag alis ko nag try ako mag bootup uli potek ayun na! back to 5 secs bootup at shutdown na siya :love::3Dance:

Walang issue yung new m2 haha ako yung may issue lol

So ayun sorry at nasayang ko mga oras niyo mga sir
:FeelsSadMan:

till next time! - Troublemaker na nag troubleshoot :3Dance:
 
Upvote 0 Downvote
ChrolloLucifer said:
UPDATE!

Hello, I'm back!!!

User problem pala to sorry na agad haha

So ganito, hindi ko pala na indicate dito na kaya ako nag install ng bagong M.2 for storage is faulty na yung lumang HHD ko o_O
Then ako naman si kamote nung dumating sinalpak ko na agad siya. Not knowing na hindi ko pala na alis yung connection ng sirang HHD o_O

Then ngayon binuksan ko uli sabi ko baka makuha pa sa reseat ng hardwares at nag reset bios pa nga ako. Tapos napansin ko yung Sata na isa naka saksak pa sa board ko. So inalis ko kasi bat nakasaksak eh hindi ko na ginagamit yun at inalis ko na sa device manager yun. Naka hide na yun Drive na yun. Pag alis ko nag try ako mag bootup uli potek ayun na! back to 5 secs bootup at shutdown na siya :love::3Dance:

Walang issue yung new m2 haha ako yung may issue lol

So ayun sorry at nasayang ko mga oras niyo mga sir
:FeelsSadMan:

till next time! - Troublemaker na nag troubleshoot :3Dance:
Click to expand...
hahaha.. sabi na eh.. hindi nga lng SSD pero faulty storage drive pa din dahilan
 
Upvote 0 Downvote
its very normal na mg slowdown yung boot if 2 nvme mo specially if mobo is hybrid pcie yung 2nd slot (as in if nasa description is sata# disable if 2nd nvme is used which means sata lane conversion in cpu) more on what nvme will trigger it ang tanong dito

best way na ma experience to is with using gigabyte aorus 4 nvme na ng pcie saturation test on post so with a 2nd nvme post slows

pero ang weird sa system nya is if hidden yung hdd
since faulty
why hindi ng high beep yung system nya indicating storage error matining yung beep ng system with faulty storage

dont tell me na walang post beep yung msi for storage problem?
 
Upvote 0 Downvote
sasame9821 said:
its very normal na mg slowdown yung boot if 2 nvme mo specially if mobo is hybrid pcie yung 2nd slot (as in if nasa description is sata# disable if 2nd nvme is used which means sata lane conversion in cpu) more on what nvme will trigger it ang tanong dito

best way na ma experience to is with using gigabyte aorus 4 nvme na ng pcie saturation test on post so with a 2nd nvme post slows

pero ang weird sa system nya is if hidden yung hdd
since faulty
why hindi ng high beep yung system nya indicating storage error matining yung beep ng system with faulty storage

dont tell me na walang post beep yung msi for storage problem?
Click to expand...
may beep sya once lang then normal na uli matagal na yun eh. Normal naman siya. Ngayon ok na ok na talaga uli haha
 
Upvote 0 Downvote
Status
Not open for further replies.

About this Thread

  • 19
    Replies
  • 988
    Views
  • 4
    Participants
Last reply from:
ChrolloLucifer

New Topics

Trending Topics

Online now

Members online
429
Guests online
1,272
Total visitors
1,701

Forum statistics

Threads
2,274,112
Posts
28,953,718
Members
1,235,078
Latest member
cjaiyes
Back
Top