🔒 Closed Udp se troubleshooting/manual

[SophiaAlexis]

CODE 1 & 2:
CAUSE 1: ip conflict
SOLUTION 1: via cmd ip resolver/ip release/renew/dns flushing
SOLUTION 2: restart modem
SOLUTION 3: vps on/off
SOLUTION 4: systemctl restart dnsmasq && service vpnserver restart
Note: varies on OS type/version

CODE 2:
SOLUTION 1: disable/enable adapter then try to connect again
SOLUTION 2: Use Softether with vpngate plugin installer instead of original

CODE 9:
CAUSE: User authentication failed
SOLUTION: check user/pass

CODE 13:
CAUSE:
SOLUTION1: recon

CODE 131:
CAUSE: no load
SOLUTION1: with load

ADD-ON: DNS Flushing
Credits:- Lawliet_1
You do not have permission to view the full content of this post. Log in or register now.
Auto ping and dns flusher + cmd tricks

 

[CL4Y]

additional ate based on my experience
ERROR CODE 131 : kulang ang load

 

[Captain Underpants]

working din yung 2 adapters, konek muna sa stable, konek din si error2, diskonek si stable, retain ni error2 un connection.. kaya stable na din siya hihi..

 

[SophiaAlexis]

salamat sa feedback--hope kahit anong error ng SE pakireport na lang po sa thread na to to serve as a guide and reference. salamat

 

[SophiaAlexis]

working din yung 2 adapters, konek muna sa stable, konek din si error2, diskonek si stable, retain ni error2 un connection.. kaya stable na din siya hihi..

di ko magets to Cap---nyahahahaha soweeee

 

[CL4Y]

salamat sa feedback--hope kahit anong error ng SE pakireport na lang po sa thread na to to serve as a guide and reference. salamat

maasahan mo ate...

 

[Shiina Mayuri]

Pwede rin alternative solution sa error code 2 disable/enable adapter then try to connect again

 

[lorc4n]

adjust niyo na lang po sa hub extension..

 

[finalgravity525]

Error Code 13 Solution: Connect lang ulit.

 

[Shiina Mayuri]

Error Code 13 Solution: Connect lang ulit.

tama ka paps puro minsan kaya pala ng error 13 is bigla na disable yung adapter hihi

 

[finalgravity525]

tama ka paps puro minsan kaya pala ng error 13 is bigla na disable yung adapter hihi

Nadidisable yung connected adapters mo paps? hmmm hindi naman nagkakaganyan sakin, nag pprompt lang si Surfalert kaya nag error code 13 sakin.

 

[Shiina Mayuri]

Nadidisable yung connected adapters mo paps? hmmm hindi naman nagkakaganyan sakin, nag pprompt lang si Surfalert kaya nag error code 13 sakin.

ganun yung akin baka damage data cable di kasi ako naka lan...

 

[Saijin God]

Error Code 13 Solution: Connect lang ulit.

Akin nag eerror 13 madalas pero nag rereconn naman afterwards Ayos to. So far error 1. 2 and 13 pa lang naman nararanasan ko and fixable naman by the said steps above

 

[CRiSBRY]

salamat dito maam thumbs up

 

[l_ctzen]

Error Code 13 Solution: Connect lang ulit.

Madalas ko ding makuha yung error na yan pero nagre-reconnect din naman agad. Pero another solution ko is ilagay yung pocket wifi (or modem sa iba) sa mas mataas na lugar or sa may bintana para hindi naba-block masyado yung connection. Not sure kung mag-work ito sa iba, sa location ko kasi mahina pa din ang hatak ng data kahit nasa second floor na ako, haha.

 

[l_ctzen]

working din yung 2 adapters, konek muna sa stable, konek din si error2, diskonek si stable, retain ni error2 un connection.. kaya stable na din siya hihi..

Salamat dito sa tip.

 

[alist1986]

Mga bosing, baka sakali lang makatulong sa frequent Error 2 ng iba.
Use Softether with vpngate plugin installer instead of original. Sa experience ko lang po ito.
PS...Nasabi ko lang ito dahil sa original SEVPN client na fresh installed sa Win10 laptop ng kapatid ko, kahit anong servers na gamitin ko ay puro error 2 lang siya. Noong ipinatong ko yung same version installer with vpngate pliugin, saka lang nag-connect yung servers.

Yung best method ni Kapitan yung the best din. If noload sim still experience error 2, switch to a direct connection if you have one or to GS-sim with freshly redeemed MB data. After connection, switch data connection back to your noload sim, and it will connect.

 

[Shiina Mayuri]

Mga bosing, baka sakali lang makatulong sa frequent Error 2 ng iba.
Use Softether with vpngate plugin installer instead of original. Sa experience ko lang po ito.

Paps mas accurate sa akin yung disable network adapter first then try to connect on your preferred server and lastly immediately enable the network adapter. It works for me most of the time and i don't need to change my apn to refresh my ip address.

 

[alist1986]

Paps mas accurate sa akin yung disable network adapter first then try to connect on your preferred server and lastly immediately enable the network adapter. It works for me most of the time and i don't need to change my apn to refresh my ip address.

Thanks. Tandaan ko lagi yan, pero di umubra kagabi sa pc na gamit ko. Kagabi kasi, nag-test ako sa laptop ng brother ko. SSL at http injectors lang yung ok,pero sa SE ayaw hanggang kanina.

 

[Shiina Mayuri]

Thanks. Tandaan ko lagi yan, pero di umubra kagabi sa pc na gamit ko. Kagabi kasi, nag-test ako sa laptop ng brother ko. SSL at http injectors lang yung ok,pero sa SE ayaw hanggang kanina.

ah ganun ba ako nga sa 3g na modem ako nag try kung uubra kasi noong araw pa ng http injector yun ang gamit ko pero pagdating kay se di ako maka connect puro error 3 nakukuha ko. 95% yung accuracy niyang trick na yan for me. hehhe