🔒 Closed Huawei b315s-936 solution for power led light only

[docperks]

Note #1: pag 98% na lang sa E3256sBootRomDownloadTool-2s then medyo matagal ibig sabihin failed(minsan may time na success kahit matagal)
Note #2: pag nag namatay na blue light then na parang nag refresh sa device manager ibig sabihin success may lalabas na success sa E3256sBootRomDownloadTool-2s

Saktong sakto po ito sa mga na stuck na sa zain/middle east/polko na v21.300


tools need:
1.balong usb downloader
You do not have permission to view the full content of this post. Log in or register now.
2.B315 service software(galing sa huawei website)
You do not have permission to view the full content of this post. Log in or register now.
3.huawei firmware v21.311
You do not have permission to view the full content of this post. Log in or register now. or You do not have permission to view the full content of this post. Log in or register now.
POLKO FIRMWARE V21.311.03.00.69
You do not have permission to view the full content of this post. Log in or register now.

4.kape

trick no. 1
1.testpoint/jumper(wag open si balong).
2.isaksak male to male usb connector.
3.install driver galing sa *B315 service software* galing sa huawei website(dapat pangalan ng sa port is *HUAWEI Mobile Connect - DownLoad port*).
4.open si E3256sBootRomDownloadTool-2s then check BootRom select mo yung kay balong na *usblsafe-b315.bin*.
check firmware select kahit anong v21.311 then click next.
5.click Scan and Upgrade, hintayin nyo lang wag mainip .
6.observe, tignan sa Note sa taas kung alin ang behavior ng application / device, pag namatay ang blue light.
7.alisin ang male to male usb connector at power adaptor.
8.saksak power adaptor, pag nag blink lang yung power led light punta ka sa trick no.2

trick no. 2
1.testpoint/jumper.
2.isaksak male to male usb connector.
3.install driver galing sa *B315 service software* galing sa huawei website(dapat pangalan ng sa port is *HUAWEI Mobile Connect - DownLoad port*)
4.open balong usb downloader load mo yung *usbloader.bin* kasama ng E3256sBootRomDownloadTool-2s(mapapansin nyo nag load pero di na detect sa PC)
5.alisin ang male to male usb connector pati power then testpoint/jumper ulit
6.open si E3256sBootRomDownloadTool-2s then check BootRom select mo yung kay balong na *usblsafe-b315.bin*.
check firmware select kahit anong v21.311 then click next.
7.click Scan and Upgrade, hintayin nyo lang wag mainip .
8.observe, tignan sa Note sa taas kung alin ang behavior ng application / device, pag namatay ang blue light.
9.alisin ang male to male usb connector at power adaptor.
10.saksak power adaptor

 

[PHC Chichicham]

Repost ata to. Parang nabasa ko na to. Credits ka naman boss sa may ari ng thread. Mahiya naman.

 

[docperks]

mukha repost no sir. galing sa kabila yan sa thread ko wala pa ko nakita ganyan na method kaya pinost ko na din dito. gusto ko lang makatulong.

 

[docperks]

 

[TresMarias]

sya din yan hahahahaha, ano magbibigay sya ng credits sa sarili nya

 

[wadzilla]

Sir san pwedeng idownload yung e3256sbootromdownloadtool-2s? Salamat!

 

[TresMarias]

tutuklawin ka na ng mga link na given by OP hahahahahahaha

 

[TheReturnOfRomansa]

diko ma install mga driver haha bakit kaya

 

[imNheMZ]

hmmm

 

[onephc]

Thanks for this thread. Yung modem ko kasi stock sa Middle East Firmware, ilang araw din ako naghanap ng solution para maibalik ko sa dating Polkomtel. Sa una, hindi ako nagkaigi pero nagawa ko rin maibalik sa Polkomtel Firmware. Thanks po.

 

[onephc]

Up for this thread.

 

[cyborg_rhaym]

pang openline po ba to?